Diskussion:Install-Party/Linux Mint Debian Edition

Aus Wiki StuRa HTW Dresden
Zur Navigation springen Zur Suche springen

Installation mit Verschlüsselung

Fail!
LMDE 3 meets https://gitlab.com/pepa65/lmdescrypt/raw/master/lmdescrypt ?

(default) disk layout

Calamares meets Btrfs

(nach der manuellen Partitionierung und) Angabe beim Programm für die Installation

cat /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a device; this may
# be used with UUID= as a more robust way to name devices that works even if
# disks are added and removed. See fstab(5).
#
# <file system>             <mount point>  <type>  <options>  <dump>  <pass>
UUID=8f303b38-b7e7-4781-aa8e-f1559b5504d2 /boot          ext4    defaults,noatime 0 2
UUID=33436381-7031-48be-8785-a48061fcabd7 /              btrfs   subvol=@,defaults,noatime,space_cache,autodefrag 0 1
UUID=33436381-7031-48be-8785-a48061fcabd7 /home          btrfs   subvol=@home,defaults,noatime,space_cache,autodefrag 0 2
UUID=641494b3-d3a2-4c57-b022-cba4d00603f5 swap           swap    defaults,noatime 0 2
cat /etc/default/grub


GRUB_CMDLINE_LINUX_DEFAULT="quiet resume=UUID=641494b3-d3a2-4c57-b022-cba4d00603f5"





cat /etc/crypttab


# /etc/crypttab: mappings for encrypted partitions.
#
# Each mapped device will be created in /dev/mapper, so your /etc/fstab
# should use the /dev/mapper/<name> paths for encrypted devices.
#
# See crypttab(5) for the supported syntax.
#
# NOTE: Do not list your root (/) partition here, it must be set up
#       beforehand by the initramfs (/etc/mkinitcpio.conf). The same applies
#       to encrypted swap, which should be set up with mkinitcpio-openswap
#       for resume support.
#
# <name>               <device>                         <password> <options>



btrfs meets luks


cat /etc/fstab


####vb
/dev/sda1               /boot   btrfs   defaults,errors=remount-ro      0    1
/dev/mapper/vg-lv--swap none    swap    sw                              0    0
/dev/mapper/vg-lv--root /       btrfs   defaults,errors=remount-ro      0    1
/dev/mapper/vg-lv--home /home   btrfs   defaults,compress=lzo           0    1
####ve
# UNCONFIGURED FSTAB FOR BASE SYSTEM
proc    /proc   proc    defaults        0       0



cat /etc/crypttab


####vb
k-ot    UUID=8765dcba-ab12-cd34-ef56-123456abcdef       none    luks
####ve



https://www.howtoforge.com/a-beginners-guide-to-btrfs



cat /etc/default/grub




####vb
#GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash kopt=root=/dev/mapper/vg-lv--root"
####ve





sbin fehlt beim PATH


dpkg -i linux-UFRII-drv-v500-de/64-bit_Driver/Debian/cnrdrvcups-ufr2-uk_5.00-1_amd64.deb




Beachten Sie: PATH von root sollte normalerweise /usr/local/sbin, /usr/sbin und /sbin enthalten



export PATH=$PATH:/usr/local/sbin:/usr/sbin:/sbin


LMDE 4 mit verschlüsselten Massenspeicher und btrfs subvolumes (möglichst noch als mirror von 2 Geräten für Massenspeicher)





LMDE 6 "anderes Dateisystem"


Vorkenntnisse vor LMDE 6


website:members/PaulRiegel/os/lmde/installation-lmde-3-mit-verschluesslung


Untersuchung Installation LMDE 6


standardmäßige Installation mit Verschlüsselung ext4 LMDE 6


nach dem Neustart in die Installation




cat /etc/crypttab


# <target name>	<source device>		<key file>	<options>
lvmlmde   UUID=3c96337f-bb08-4f9d-ba25-fe5d23afd680   none   luks,discard,tries=3



cat /etc/fstab


#### Static Filesystem Table File
proc	/proc	proc	defaults	0	0
# /dev/mapper/lvmlmde-root
UUID=ba9df8e4-a4fb-42f6-b3ef-682d8c3edd95 /  ext4 defaults 0 1
# /dev/mapper/lvmlmde-swap
UUID=9e412642-d11a-40f2-9c59-03f9a51f5e28 none   swap sw 0 0
# /dev/sda2
UUID=22a7ba7f-0999-43d8-90f2-34c85af6f167 /boot  ext4 defaults 0 1
# /dev/sda1
UUID=C002-8E9D /boot/efi  vfat defaults 0 1



cat /etc/default/grub.d/61_live-installer.cfg


#! /bin/sh
set -e

GRUB_CMDLINE_LINUX="cryptdevice=UUID=3c96337f-bb08-4f9d-ba25-fe5d23afd680:lvmlmde root=/dev/mapper/lvmlmde-root resume=/dev/mapper/lvmlmde-swap"



standardmäßige Installation ohne Verschlüsselung btrfs LMDE 6


während der Installation




mount


sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,relatime)
udev on /dev type devtmpfs (rw,nosuid,relatime,size=3743316k,nr_inodes=935829,mode=755,inode64)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000)
tmpfs on /run type tmpfs (rw,nosuid,nodev,noexec,relatime,size=757356k,mode=755,inode64)
/dev/sdb1 on /run/live/medium type iso9660 (ro,noatime,nojoliet,check=s,map=n,blocksize=2048,iocharset=utf8)
/dev/loop0 on /run/live/rootfs/filesystem.squashfs type squashfs (ro,noatime,errors=continue)
tmpfs on /run/live/overlay type tmpfs (rw,noatime,mode=755,inode64)
overlay on / type overlay (rw,noatime,lowerdir=/run/live/rootfs/filesystem.squashfs/,upperdir=/run/live/overlay/rw,workdir=/run/live/overlay/work,redirect_dir=on)
tmpfs on /usr/lib/live/mount type tmpfs (rw,nosuid,nodev,noexec,relatime,size=757356k,mode=755,inode64)
/dev/sdb1 on /usr/lib/live/mount/medium type iso9660 (ro,noatime,nojoliet,check=s,map=n,blocksize=2048,iocharset=utf8)
/dev/loop0 on /usr/lib/live/mount/rootfs/filesystem.squashfs type squashfs (ro,noatime,errors=continue)
tmpfs on /usr/lib/live/mount/overlay type tmpfs (rw,noatime,mode=755,inode64)
securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime)
tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev,inode64)
tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k,inode64)
cgroup2 on /sys/fs/cgroup type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate,memory_recursiveprot)
pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime)
efivarfs on /sys/firmware/efi/efivars type efivarfs (rw,nosuid,nodev,noexec,relatime)
bpf on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,relatime,mode=700)
systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=29,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=12771)
mqueue on /dev/mqueue type mqueue (rw,nosuid,nodev,noexec,relatime)
debugfs on /sys/kernel/debug type debugfs (rw,nosuid,nodev,noexec,relatime)
tracefs on /sys/kernel/tracing type tracefs (rw,nosuid,nodev,noexec,relatime)
hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime,pagesize=2M)
configfs on /sys/kernel/config type configfs (rw,nosuid,nodev,noexec,relatime)
fusectl on /sys/fs/fuse/connections type fusectl (rw,nosuid,nodev,noexec,relatime)
ramfs on /run/credentials/systemd-sysusers.service type ramfs (ro,nosuid,nodev,noexec,relatime,mode=700)
ramfs on /run/credentials/systemd-tmpfiles-setup-dev.service type ramfs (ro,nosuid,nodev,noexec,relatime,mode=700)
ramfs on /run/credentials/systemd-sysctl.service type ramfs (ro,nosuid,nodev,noexec,relatime,mode=700)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,relatime,inode64)
ramfs on /run/credentials/systemd-tmpfiles-setup.service type ramfs (ro,nosuid,nodev,noexec,relatime,mode=700)
binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,nosuid,nodev,noexec,relatime)
tmpfs on /run/user/1000 type tmpfs (rw,nosuid,nodev,relatime,size=757356k,nr_inodes=189339,mode=700,uid=1000,gid=1000,inode64)
gvfsd-fuse on /run/user/1000/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,relatime,user_id=1000,group_id=1000)
portal on /run/user/1000/doc type fuse.portal (rw,nosuid,nodev,relatime,user_id=1000,group_id=1000)
/dev/loop0 on /source type squashfs (ro,relatime,errors=continue)
/dev/sda3 on /target type btrfs (rw,relatime,ssd,space_cache=v2,subvolid=256,subvol=/@)
/dev/sda3 on /target/home type btrfs (rw,relatime,ssd,space_cache=v2,subvolid=257,subvol=/@home)
/dev/sda2 on /target/boot type btrfs (rw,relatime,ssd,space_cache=v2,subvolid=5,subvol=/)



nach dem Neustart in die Installation




cat /etc/crypttab


# <target name>	<source device>		<key file>	<options>



cat /etc/fstab


#### Static Filesystem Table File
proc	/proc	proc	defaults	0	0
# /dev/sda3
UUID=b84bec73-29b9-4e62-a830-5069650680af	/	btrfs	defaults,subvol=@	00
UUID=b84bec73-29b9-4e62-a830-5069650680af	/home	btrfs	defaults,subvol=@home	0	0
# /dev/sda2
UUID=dea84151-1736-439a-8127-a45f2a7feb75	/boot	btrfs	defaults	0	0
# /dev/sda1
UUID=FDD2-C26F	/boot/efi	vfat	defaults	0	1



cat /etc/default/grub.d/61_live-installer.cfg


Erarbeitung Verschlüsslung und btrfs


https://forums.linuxmint.com/viewtopic.php?t=100659



meets


https://linuxmint.com/rel_faye.php



sudo live-installer-expert-mode


/target ist die das gewünschte Ziel!
Alles Nachfolgende wird aber noch mit /mnt/target angegeben.



sudo mkdir /mnt/target


sudo mount -o subvol=@ /dev/mapper/lvmlmde-root /mnt/target


sudo mkdir /mnt/target/home


sudo mount -o subvol=home /dev/mapper/lvmlmde-root /mnt/target/home


sudo rsync -avz /run/live/medium/casper/filesystem.squashfs/ /mnt/target/

/dev/loop0


sudo mkdir /mnt/target/dev


sudo mount --bind /dev /mnt/target/dev


sudo mkdir /dev/pts /mnt/target/dev/pts


sudo mount --bind /dev/pts /mnt/target/dev/pts


sudo mkdir /mnt/target/dev/shm


sudo mount --bind /dev/shm /mnt/target/dev/shm


sudo mkdir /mnt/target/proc


sudo mount --bind /proc /mnt/target/proc


sudo mkdir /mnt/target/sys


sudo mount --bind /sys /mnt/target/sys


sudo mkdir /mnt/target/tmp


sudo mount --bind /tmp /mnt/target/tmp


sudo mkdir /mnt/target/


cp -f /etc/resolv.conf /mnt/target/etc/resolv.conf


chroot /mnt/target


Installation Debian


und dann Wechsel zu LMDE

https://forums.linuxmint.com/viewtopic.php?t=404823



(bevorzugte) Verwendung von zram aktivieren


Bei einer standardmäßigen Installation (ohne Verschlüsselung) mit btrfs wird anscheinend keine Partition (und keine Datei) für SWAP erstellt. (Gut! Stattdessen kann - zeitgemäßer - zram verwendet werden.)



apt install zram-tools




systemctl status zramswap.service




systemctl is-enabled zramswap.service


enabled



systemctl is-active zramswap.service


active



LMDE 6 meets OpenZFS


LMDE 6 OpenZFS Annahmen


Verwendung mehrerer Geräte für Massenspeicher


nicht notwendig


Für einen hohen Ansprch, soll die Konfiguration 2 Geräte für Massenspeicher vorsehen, um darzustellen, dass ein (nahezu) beliebiger Verbund an Geräte für Massenspeicher verwendet werden kann.



Deaktivierung Secure Boot


in der Verwaltung vom Gerät wikipedia:de:Unified Extensible Firmware Interface#Secure Boot deaktivieren



wegen der nachträglichen Installation ist der Schlüssel für das Modul für den Kernel für ZFS nicht valide, weswegen das Modul nicht benutzt werden kann


sudo modprobe zfs


modprobe: ERROR: could not insert 'zfs': Key was rejected by service








LMDE 6 OpenZFS Vorbereitung




mit dem Internet verbinden





whoami


mint



uname -a


Linux mint 6.1.0-12-amd64 #1 SMP PREEMPT_DYNAMIC Debian 6.1.52-1 (2023-09-07) x86_64 GNU/Linux



LMDE 6 OpenZFS Einrichtung Umgebung Installation


apt update




sudo apt -y install ssh




sudo systemctl status ssh




Ersetzen vom nicht gesetzen Passwort



passwd




ip a






ssh mint@321.321.321.321






sudo nano /etc/apt/sources.list


#/etc/apt/sources.list
deb http://deb.debian.org/debian bookworm main contrib non-free-firmware



apt update




gsettings set org.gnome.desktop.media-handling automount false




apt -y install debootstrap gdisk zfsutils-linux




LMDE 6 OpenZFS Einrichtung Geräte für Massenspeicher


ls -la /dev/disk/by-id/


total 0



lrwxrwxrwx 1 root root   9 May 28 23:25 ata-Samsung_SSD_750_EVO_500GB_S363NWAH718728R -> ../../sda



lrwxrwxrwx 1 root root   9 May 28 23:25 ata-Samsung_SSD_850_EVO_M.2_500GB_S33DNX0H809148M -> ../../sdb



lrwxrwxrwx 1 root root   9 May 28 23:25 usb-Kingston_DataTraveler_3.0_4CEDFB74A418B320F9950BCC-0:0 -> ../../sdc
lrwxrwxrwx 1 root root  10 May 28 23:25 usb-Kingston_DataTraveler_3.0_4CEDFB74A418B320F9950BCC-0:0-part1 -> ../../sdc1
lrwxrwxrwx 1 root root  10 May 28 23:25 usb-Kingston_DataTraveler_3.0_4CEDFB74A418B320F9950BCC-0:0-part2 -> ../../sdc2



lrwxrwxrwx 1 root root   9 May 28 23:25 wwn-0x5002538d41306eb7 -> ../../sdb



lrwxrwxrwx 1 root root   9 May 28 23:25 wwn-0x5002538d702e43f9 -> ../../sda








DISK1=/dev/disk/by-id/ata-Samsung_SSD_750_EVO_500GB_S363NWAH718728R


DISK2=/dev/disk/by-id/ata-Samsung_SSD_850_EVO_M.2_500GB_S33DNX0H809148M


swapoff -a


cat /proc/mdstat




Personalities : 
unused devices: <none>








sudo wipefs -a $DISK1


/dev/disk/by-id/ata-Samsung_SSD_750_EVO_500GB_S363NWAH718728R: 8 bytes were erased at offset 0x00000200 (gpt): 45 46 49 20 50 41 52 54
/dev/disk/by-id/ata-Samsung_SSD_750_EVO_500GB_S363NWAH718728R: 8 bytes were erased at offset 0x7470c05e00 (gpt): 45 46 49 20 50 41 52 54
/dev/disk/by-id/ata-Samsung_SSD_750_EVO_500GB_S363NWAH718728R: 2 bytes were erased at offset 0x000001fe (PMBR): 55 aa
/dev/disk/by-id/ata-Samsung_SSD_750_EVO_500GB_S363NWAH718728R: calling ioctl to re-read partition table: Success



sudo wipefs -a $DISK2


/dev/disk/by-id/ata-Samsung_SSD_850_EVO_M.2_500GB_S33DNX0H809148M: 8 bytes were erased at offset 0x00000200 (gpt): 45 46 49 20 50 41 52 54
/dev/disk/by-id/ata-Samsung_SSD_850_EVO_M.2_500GB_S33DNX0H809148M: 8 bytes were erased at offset 0x7470c05e00 (gpt): 45 46 49 20 50 41 52 54
/dev/disk/by-id/ata-Samsung_SSD_850_EVO_M.2_500GB_S33DNX0H809148M: 2 bytes were erased at offset 0x000001fe (PMBR): 55 aa
/dev/disk/by-id/ata-Samsung_SSD_850_EVO_M.2_500GB_S33DNX0H809148M: calling ioctl to re-read partition table: Success



sudo blkdiscard -f $DISK1


blkdiscard: Operation forced, data will be lost!



sudo blkdiscard -f $DISK2


blkdiscard: Operation forced, data will be lost!



sudo sgdisk --zap-all $DISK1


Creating new GPT entries in memory.
GPT data structures destroyed! You may now partition the disk using fdisk or
other utilities.



sudo sgdisk --zap-all $DISK2


Creating new GPT entries in memory.
GPT data structures destroyed! You may now partition the disk using fdisk or
other utilities.



sudo sgdisk -n2:1M:+512M -t2:EF00 $DISK1


Creating new GPT entries in memory.
The operation has completed successfully.



sudo sgdisk -n2:1M:+512M -t2:EF00 $DISK2


Creating new GPT entries in memory.
The operation has completed successfully.



sudo sgdisk -n3:0:+1G -t3:BF01 $DISK1


The operation has completed successfully.



sudo sgdisk -n3:0:+1G -t3:BF01 $DISK2


The operation has completed successfully.



sudo sgdisk -n4:0:0 -t4:BF00 $DISK1


The operation has completed successfully.



sudo sgdisk -n4:0:0 -t4:BF00 $DISK2


The operation has completed successfully.



sudo zpool create \
    -o compatibility=grub2 \
    -o ashift=12 \
    -o autotrim=on \
    -o cachefile=/etc/zfs/zpool.cache \
    -O devices=off \
    -O acltype=posixacl\
    -O xattr=sa \
    -O compression=lz4 \
    -O normalization=formD \
    -O relatime=on \
    -O canmount=off \
    -O mountpoint=/boot -R /mnt \
    bpool mirror \
    ${DISK1}-part3 \
    ${DISK2}-part3







zpool create \
    -O keylocation=prompt \
    -O keyformat=passphrase \
    -o ashift=12 \
    -o autotrim=on \
    -O encryption=on \
    -O acltype=posixacl \
    -O xattr=sa \
    -O dnodesize=auto \
    -O compression=lz4 \
    -O normalization=formD \
    -O relatime=on \
    -O canmount=off \
    -O mountpoint=/ -R /mnt \
    rpool mirror \
    ${DISK1}-part4 \
    ${DISK2}-part4







sudo zfs create -o canmount=off -o mountpoint=none rpool/ROOT


sudo zfs create -o canmount=off -o mountpoint=none bpool/BOOT


sudo zfs create -o canmount=noauto -o mountpoint=/ rpool/ROOT/debian


sudo zfs mount rpool/ROOT/debian


sudo zfs create -o mountpoint=/boot bpool/BOOT/debian


sudo zfs create                     rpool/home


sudo zfs create -o mountpoint=/root rpool/home/root


sudo chmod 700 /mnt/root


sudo zfs create -o canmount=off     rpool/var


sudo zfs create -o canmount=off     rpool/var/lib


sudo zfs create                     rpool/var/log


sudo zfs create                     rpool/var/spool


sudo zfs create -o com.sun:auto-snapshot=false rpool/var/cache


sudo zfs create -o com.sun:auto-snapshot=false rpool/var/lib/nfs


sudo zfs create -o com.sun:auto-snapshot=false rpool/var/tmp


sudo chmod 1777 /mnt/var/tmp


sudo zfs create rpool/srv
sudo zfs create -o canmount=off rpool/usr


sudo zfs create rpool/usr/local
sudo zfs create rpool/var/lib/AccountsService


sudo zfs create rpool/var/lib/NetworkManager
sudo zfs create -o com.sun:auto-snapshot=false rpool/var/lib/docker
sudo zfs create rpool/var/snap
sudo zfs create rpool/var/www
sudo zfs create -o com.sun:auto-snapshot=false  rpool/tmp


sudo chmod 1777 /mnt/tmp
apt search systemd-timesyncd
i   systemd-timesyncd                 - minimalistic service to synchronize local ti
p   systemd-timesyncd:i386            - minimalistic service to synchronize local ti

apt search dosfstools
i   dosfstools                        - utilities for making and checking MS-DOS FAT
p   dosfstools:i386                   - utilities for making and checking MS-DOS FAT
</code>

: <code>nano /etc/fstab</code>
<pre>
#### Static Filesystem Table File
proc    /proc   proc    defaults        0       0

mkdosfs -F 32 -s 1 -n EFI ${DISK1}-part2
mkfs.fat 4.2 (2021-01-31)

mkdir /boot/efi
echo /dev/disk/by-uuid/$(blkid -s UUID -o value ${DISK1}-part2) \
   /boot/efi vfat defaults 0 0 >> /etc/fstab</code>



cat /etc/fstab
#### Static Filesystem Table File
proc    /proc   proc    defaults        0       0
/dev/disk/by-uuid/A7AA-5E96 /boot/efi vfat defaults 0 0

mount /boot/efi
mount: (hint) your fstab has been modified, but systemd still uses
       the old version; use 'systemctl daemon-reload' to reload.

LMDE 6 OpenZFS Installation LMDE GUI II








Abgerufen von „https://wiki.stura.htw-dresden.de/index.php?title=Diskussion:Install-Party/Linux_Mint_Debian_Edition&oldid=44678“