Diskussion:Install-Party/Linux Mint Debian Edition: Unterschied zwischen den Versionen

Aus Wiki StuRa HTW Dresden
Zur Navigation springen Zur Suche springen
(Neuer Abschnitt →‎(default) disk layout)
Zeile 3: Zeile 3:
; Fail!
; Fail!
: LMDE 3 meets https://gitlab.com/pepa65/lmdescrypt/raw/master/lmdescrypt ?
: LMDE 3 meets https://gitlab.com/pepa65/lmdescrypt/raw/master/lmdescrypt ?
== (default) disk layout ==
; Calamares meets Btrfs:
(nach der mauellen Partitionierung und) Angabe beim Programm für die Installation
: <code>cat /etc/fstab</code>
<pre>
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a device; this may
# be used with UUID= as a more robust way to name devices that works even if
# disks are added and removed. See fstab(5).
#
# <file system>            <mount point>  <type>  <options>  <dump>  <pass>
UUID=8f303b38-b7e7-4781-aa8e-f1559b5504d2 /boot          ext4    defaults,noatime 0 2
UUID=33436381-7031-48be-8785-a48061fcabd7 /              btrfs  subvol=@,defaults,noatime,space_cache,autodefrag 0 1
UUID=33436381-7031-48be-8785-a48061fcabd7 /home          btrfs  subvol=@home,defaults,noatime,space_cache,autodefrag 0 2
UUID=641494b3-d3a2-4c57-b022-cba4d00603f5 swap          swap    defaults,noatime 0 2
</pre>
: <code>cat /etc/default/grub</code>
<pre></pre>
<pre>
GRUB_CMDLINE_LINUX_DEFAULT="quiet resume=UUID=641494b3-d3a2-4c57-b022-cba4d00603f5"
</pre>
<pre></pre>
: <code>cat /etc/crypttab</code>
<pre>
# /etc/crypttab: mappings for encrypted partitions.
#
# Each mapped device will be created in /dev/mapper, so your /etc/fstab
# should use the /dev/mapper/<name> paths for encrypted devices.
#
# See crypttab(5) for the supported syntax.
#
# NOTE: Do not list your root (/) partition here, it must be set up
#      beforehand by the initramfs (/etc/mkinitcpio.conf). The same applies
#      to encrypted swap, which should be set up with mkinitcpio-openswap
#      for resume support.
#
# <name>              <device>                        <password> <options>
</pre>

Version vom 11. September 2018, 21:07 Uhr

Installation mit Verschlüsselung

Fail!
LMDE 3 meets https://gitlab.com/pepa65/lmdescrypt/raw/master/lmdescrypt ?

(default) disk layout

Calamares meets Btrfs

(nach der mauellen Partitionierung und) Angabe beim Programm für die Installation

cat /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a device; this may
# be used with UUID= as a more robust way to name devices that works even if
# disks are added and removed. See fstab(5).
#
# <file system>             <mount point>  <type>  <options>  <dump>  <pass>
UUID=8f303b38-b7e7-4781-aa8e-f1559b5504d2 /boot          ext4    defaults,noatime 0 2
UUID=33436381-7031-48be-8785-a48061fcabd7 /              btrfs   subvol=@,defaults,noatime,space_cache,autodefrag 0 1
UUID=33436381-7031-48be-8785-a48061fcabd7 /home          btrfs   subvol=@home,defaults,noatime,space_cache,autodefrag 0 2
UUID=641494b3-d3a2-4c57-b022-cba4d00603f5 swap           swap    defaults,noatime 0 2
cat /etc/default/grub

GRUB_CMDLINE_LINUX_DEFAULT="quiet resume=UUID=641494b3-d3a2-4c57-b022-cba4d00603f5"

cat /etc/crypttab
# /etc/crypttab: mappings for encrypted partitions.
#
# Each mapped device will be created in /dev/mapper, so your /etc/fstab
# should use the /dev/mapper/<name> paths for encrypted devices.
#
# See crypttab(5) for the supported syntax.
#
# NOTE: Do not list your root (/) partition here, it must be set up
#       beforehand by the initramfs (/etc/mkinitcpio.conf). The same applies
#       to encrypted swap, which should be set up with mkinitcpio-openswap
#       for resume support.
#
# <name>               <device>                         <password> <options>